Latest revision as of 21:58, 27 September 2024

Debian 12

Set IP

Find the interface name.

nmcli c show

Configure IP settings.

nmcli con mod "Wired connection 1" ipv4.addresses 10.13.13.235/24 ipv4.method manual
nmcli con mod "Wired connection 1" ipv4.gateway 10.13.13.254
nmcli con mod "Wired connection 1" ipv4.dns "10.13.13.240"

For mutiple IP or DNS settings.

nmcli con mod "Wired connection 1" ipv4.addresses 10.13.13.235/24, 192.168.1.235/24 ipv4.method manual
nmcli con mod "Wired connection 1" ipv4.dns "8.8.8.8, 8.8.4.4"

Reset interface

Reset or reboot.

nmcli con down "Wired connection 1" && nmcli con up "Wired connection 1"

Show Settings

nmcli -p connection show "Wired connection 1"

Debian 11

interfaces

make sure the interfaces file has not been modified.

vi /etc/network/interfaces

The default settings are:

# interfaces(5) file used by ifup(8) and ifdown(8)

# Please note that this file is written to be used with dhcpcd
# For static IP, consult /etc/dhcpcd.conf and 'man dhcpcd.conf'

# Include files from /etc/network/interfaces.d:
source-directory /etc/network/interfaces.d

dhcpcd.conf

vi /etc/dhcpcd.conf

Append the following. The entry of static will stop the server looking for an IP address from DHCP.

interface eth0
static ip_address=192.168.13.200/24
static routers=192.168.13.1
static domain_name_servers=8.8.8.8 8.8.4.4
static domain_search=mydomain.com ap.mydomain.com

Alias

Temporary

To create a temporary alias rather than a permanent one you can issue the following command from the CLI.

ifconfig eth0:0 192.168.22.1/24

IPv6

The domain names servers can have a mix of IPv4 and IPv6 servers.

vi /etc/dhcpcd.conf

static ip6_address=2321:3fa4:4f7a:d100::1234/64
static domain_name_servers=2001:4860:4860::8888 2001:4860:4860::8844

VLAN

Load 8021q Module

vi /etc/modules

Add the line

8021q

Create Interface

Define a VLAN for a specific interface.

vi /etc/network/interfaces

# VLAN 101 Interface
auto eth0.101
iface eth0.101 inet manual
    vlan-raw-device eth0

Assign IP Address

Set a static IP for new interface

vi /etc/dhcpcd.conf

# Static IP configuration for VLan.101
interface eth0.101
static ip_address=192.168.1.101/24

Static Route

vi /lib/dhcpcd/dhcpcd-hooks/40-routes

This will add a static route via interface eth0.11 which is on Vlan.11. you could just specify eth0.

ip route add 192.168.0.0/16 via 192.168.99.254 dev eth0.11 proto static

Restart Interface

ip link set eth0 down && ip link set eth0 up

@@ Line 1: / Line 1: @@
-= interfaces =
+= Debian 12 =
+== Set IP ==
+Find the interface name.
+<pre>nmcli c show</pre>
+Configure IP settings.
+<pre>
+nmcli con mod "Wired connection 1" ipv4.addresses 10.13.13.235/24 ipv4.method manual
+nmcli con mod "Wired connection 1" ipv4.gateway 10.13.13.254
+nmcli con mod "Wired connection 1" ipv4.dns "10.13.13.240"
+</pre>
+For mutiple IP or DNS settings.
+<pre>
+nmcli con mod "Wired connection 1" ipv4.addresses 10.13.13.235/24, 192.168.1.235/24 ipv4.method manual
+nmcli con mod "Wired connection 1" ipv4.dns "8.8.8.8, 8.8.4.4"
+</pre>
+== Reset interface ==
+Reset or reboot.
+<pre>nmcli con down "Wired connection 1" && nmcli con up "Wired connection 1"</pre>
+== Show Settings ==
+<pre>nmcli -p connection show "Wired connection 1"</pre>
+</pre>
+= Debian 11 =
+== interfaces ==
 make sure the interfaces file has not been modified.
 <pre>
@@ Line 13: / Line 46: @@
 # Include files from /etc/network/interfaces.d:
 source-directory /etc/network/interfaces.d
-auto lo
-iface lo inet loopback
-iface eth0 inet manual
-allow-hotplug wlan0
-iface wlan0 inet manual
-    wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
-allow-hotplug wlan1
-iface wlan1 inet manual
-    wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf
 </pre>
-= dhcpcd.conf =
+== dhcpcd.conf ==
 <pre>
 vi /etc/dhcpcd.conf
@@ Line 43: / Line 63: @@
 </pre>
-= Alias =
+== Alias ==
-== Temporary ==
+=== Temporary ===
 To create a temporary alias rather than a permanent one you can issue the following command from the CLI.
 <pre>
@@ Line 51: / Line 71: @@
 </pre>
-= IPv6 =
+== IPv6 ==
-I haven't figured out a way for this to work with configuration file dhcpcd.conf.
+The domain names servers can have a mix of IPv4 and IPv6 servers.
-<pre>
-vi /etc/network/interfaces
-</pre>
-<pre>
-auto eth0
-iface eth0 inet6 static
-address 2321:3fa4:4f7a:d100::1234
-netmask 56
-gateway 2321:3fa4:4f7a:d100::ffff
-</pre>
-Edit dhcpcd.conf for name servers
 <pre>
 vi /etc/dhcpcd.conf
@@ Line 72: / Line 79: @@
 <pre>
+static ip6_address=2321:3fa4:4f7a:d100::1234/64
 static domain_name_servers=2001:4860:4860::8888 2001:4860:4860::8844
 </pre>
-= VLAN =
+== VLAN ==
-== Load 8021q Module ==
+=== Load 8021q Module ===
 <pre>
 vi /etc/modules
@@ Line 87: / Line 95: @@
 </pre>
-== Create Interface ==
+=== Create Interface ===
 Define a VLAN for a specific interface.
@@ Line 101: / Line 109: @@
 </pre>
-== Assign IP Address ==
+=== Assign IP Address ===
 Set a static IP for new interface
 <pre>
@@ Line 108: / Line 116: @@
 <pre>
-# Static IP configuration for VLan.10
+# Static IP configuration for VLan.101
 interface eth0.101
 static ip_address=192.168.1.101/24
 </pre>
+== Static Route ==
+<pre>
+vi /lib/dhcpcd/dhcpcd-hooks/40-routes
+</pre>
+This will add a static route via interface eth0.11 which is on Vlan.11.  you could just specify eth0.
+<pre>
+ip route add 192.168.0.0/16 via 192.168.99.254 dev eth0.11 proto static
+</pre>
+== Restart Interface ==
+<pre>ip link set eth0 down && ip link set eth0 up</pre>
 [[Category : Raspbian]]

Static IP Address for Raspbian: Difference between revisions